We use a press tool to join copper and PEX fittings without an open flame. It is faster and safer when we are working near wood framing or insulation.
Bathroom Plumbing Remodeling in gilbert done right the first time
Bathroom Plumbing Remodeling in gilbert means tearing out old fixtures, rerouting supply and drain lines, and setting new valves so your tile and trim drop in clean. We handle everything from the shutoff to the shower head.
Serving gilbert and nearby areas.
How big is the job?
Full rough-in
New supply and drain lines with a layout change.
- 1. Fixture swap Replace toilet, faucet, and shower trim using existing rough-in.
- 2. Full rough-in New supply and drain lines with a layout change.
- 3. Slab and sewer Move drains, cut concrete, repair sewer sections.
Drag the needle to compareTouch and drag the needle
- 23Services from one local team
- 27Areas served around gilbert
- Camera firstWe inspect the drain before closing walls
- Pressure testEvery line is tested before tile goes down
What our Bathroom Plumbing Remodeling includes
Our scope covers the plumbing work from demo to final fixture set.
Work order
Bathroom Plumbing Remodeling- Demo and disposal: We pull the old toilet, tub, vanity, and shutoff valves. Failing pipe gets cut out and hauled away. You do not need to rent a dumpster for the plumbing demo.
- New supply lines: We run new PEX tubing or copper pipe from the main to every fixture. That includes hot and cold lines for the sink, shower, and toilet. Every connection is pressure tested before the wall closes.
- Drain and vent rough-in: New ABS pipe for the tub, shower, and sink drains ties into the existing stack. We set the vent to Uniform Plumbing Code (UPC) requirements so the inspector signs off without a redo.
- Valve and flange set: We install the shower valve body, tub drain, and toilet flange to match your finished floor height. The valve body is set plumb and level so the trim plate sits flush against the tile.
- Final fixture install: After tile and paint, we set the toilet, faucets, shower head, and accessories. We use new wax rings and Teflon tape on every threaded connection. Then we run water and check for drips.
What the first visit covers
First visit
We walk the bathroom, mark fixture locations, and check the main stack and shutoffs.
Bathroom Plumbing Remodeling at homes
We handle remodels in gilbert houses from single vanity swaps to full master bath rebuilds.
Master bath gut
New rough-in for shower, tub, and double vanity.
Hall bath update
Replace toilet, faucet, and shower valve.
Curbless shower
Linear drain rough-in set to tile plan.
Toilet relocation
Slab cut and new drain tied to main stack.
Bathroom Plumbing Remodeling at businesses
We remodel restrooms in gilbert offices, retail spaces, and restaurants.
Office restrooms
ADA fixture heights and floor drains.
Retail bathrooms
Commercial-grade shutoffs and easy-clean drains.
Restaurant restrooms
Grease-resistant lines and backflow testing.
What Bathroom Plumbing Remodeling in gilbert covers
A bathroom remodel is the one time you can replace the plumbing behind the wall without tearing up finished tile. Do it right once and you avoid a second demo later.
Bathroom Plumbing Remodeling in gilbert is the plumbing scope of a bathroom renovation: removing the old toilet, tub, and vanity, then running new PEX tubing or copper pipe for the shower valve, sink, and toilet supply. We cut out failing ABS pipe, re-solder or press new fittings, and set a new wax ring so the toilet seals flat. If you are moving a drain or adding a second sink, we cut the slab or frame the wall and run the new line to the main stack.
Most gilbert homes built before 2005 still have original builder-grade shutoff valves and 1/2-inch copper that has seen 20 summers of hard water. That scale buildup drops your shower pressure and shortens water heater life. A bathroom plumbing services gilbert crew can swap those valves and lines during the remodel instead of after the tile is up. We also check for slab leaks and root intrusion in the sewer line while the floor is open.
- What it is
- Plumbing rough-in and fixture set during a bathroom renovation.
- When it helps
- When you are moving fixtures or replacing old pipe.
- What you get
- New supply lines, drains, valves, and tested connections.
How our bathroom remodel plumbing process works
Every job follows the same five steps. You always know what is happening and what comes next.
Tools and methods we use on bathroom remodels
Each method answers a different question. Together they leave very little to guess.
A camera on a flexible reel lets us see inside the drain and sewer line. We check for root intrusion, bellies, and construction debris before the floor closes.
This microphone-style tool picks up the sound of water escaping a pipe under the slab. It tells us where to break concrete instead of guessing.
For copper pipe connections that need a soldered joint, we use a propane torch and lead-free solder. We shield the framing with a heat cloth.
We clear the branch line after demo with a drain snake or auger. That removes grout, drywall dust, and scale before the new fixture goes on.
When gilbert homeowners call us for bathroom plumbing
A 1990s gilbert home with original copper and a failing shower valve needs a full master bath update.
We cut out the old copper, run new PEX tubing to the shower, tub, and double vanity, and set a new Moen…
HomesA homeowner wants to move the toilet to fit a larger vanity and freestanding tub.
We cut the slab, reroute the 3-inch drain to the new location, and tie it into the main stack with a proper…
HomesA hall bathroom remodel uncovers a slab leak and root intrusion in the sewer line.
We locate the slab leak with acoustic equipment, break out the concrete, and repair the line.
HomesA homeowner wants a curbless shower and a new tub filler but does not know if the drain can move.
We measure the joist direction and drain slope, then design a linear drain rough-in that meets Uniform Plumbing Code (UPC).
Homes
How Bathroom Plumbing Remodeling works in gilbert
Gilbert sits in Maricopa County, where summer attic temperatures hit 140 degrees and water lines bake. That heat, plus hard water at 12 to 18 grains per gallon, is why shower valves and shutoff valves fail earlier here than in cooler markets.
Agritopia
Many homes here have original 2000s-era fixtures. We often find failing shutoff valves and scale buildup in the shower cartridges during demo.
Power Ranch
The soil in this area shifts with irrigation cycles, which puts stress on slab plumbing. We camera the drain and check for slab leaks while the floor is open.
Val Vista Lakes
Larger master baths here often get full gut remodels. We move drains and run new PEX lines to double vanities and freestanding tubs.
- Agritopia
- Power Ranch
- Val Vista Lakes
- Gilbert Heritage District
From problem to finished result.
Slide to compare the photo with an illustrative inspection view. It is generated from the photo, not a measurement.
PhotoMaster bath rough-in and valve swap
Before: A 2001 gilbert home had original copper lines, a frozen shutoff valve, and a shower cartridge packed with scale. The shower ran at a trickle and the handle was hard to turn.
After: We replaced the branch with PEX tubing, set a new Moen valve, and installed new quarter-turn shutoffs. Shower pressure went from 1.8 to 4.2 gallons per minute. The inspector passed the rough-in on the first visit.
Toilet move with slab cut
Before: A homeowner wanted a larger vanity, which meant moving the toilet 14 inches. The original drain was cast iron and starting to scale shut.
After: We cut the slab, rerouted the 3-inch drain with PVC pipe, and set a new flange level with the tile. The toilet sits flat with no rock. Drain flow tested at full capacity with no gurgle.
Slab leak and sewer root repair
Before: During demo on a hall bath remodel, we found a warm spot on the floor and a slow drain. The camera showed root intrusion in the clay sewer line under the slab.
After: We located the slab leak with acoustic equipment, repaired the line, and replaced 8 feet of root-damaged sewer with PVC pipe. The drain flows clear.
Bathroom plumbing problems we solve during a remodel
Here are the issues we find most often behind gilbert bathroom walls.
Frozen or stuck shutoff valves
A valve that will not close means you cannot isolate the bathroom during a repair.
Hard water scale in the shower valve
Scale buildup in the cartridge drops your shower to a trickle and shortens the valve life. It also makes the handle stiff and hard to turn.
Root intrusion in the sewer line
Roots find the smallest crack in old clay or cast iron pipe.
Slab leak under the bathroom floor
A slab leak warms the floor and quietly drives up your water bill.
Why upgrade your bathroom plumbing now
A bathroom remodel is the only time you can replace the hidden plumbing without tearing up finished tile.
Better water pressure
Old galvanized or scaled copper lines choke flow to a trickle.
No more hidden leaks
A slow drip behind the wall rots framing and grows mold.
Code-correct rough-in
Gilbert follows the Uniform Plumbing Code (UPC), and inspectors check venting, trap arms, and shutoff placement.
Fixtures that last
We install Moen, Delta, and Kohler valves with matching trim.
Bathroom Plumbing Remodeling cost in gilbert
A simple fixture swap with no layout change sits near the low end.
Included
Quoted after a first look
- Demo and disposal
- New supply lines
- Drain and vent rough-in
- Valve and flange set
What changes the scope
Quoted after a first look
- Layout changes
- Pipe material found
- Fixture grade
- Hidden damage
What you receive
Clear records you can keep and share.
Written scope
Fixture locations and pipe routes listed before work starts.
Pressure test record
Gauge reading noted after the rough-in holds.
Camera findings
Notes on drain condition and any root intrusion found.
Bathroom plumbing experience you can count on
We have been plumbing gilbert homes since 2016, and bathroom remodels are a core part of our work.
Drain slope
We check the fall per foot to confirm waste flows to the stack.
Vent height
We measure the vent above the fixture to meet code.
Shutoff condition
We test each valve to see if it closes fully.
Is your gilbert area covered?
Type your ZIP code or neighborhood and we will confirm. If yours is not listed, ask.
gilbert ZIP codes
- 85233
- 85234
- 85236
- 85297
- 85296
- 85295
- 85298
- 85244
- 85299
Towns we serve.
Based in gilbert and covering the places around it. Pick one for local details.
What gilbert homeowners say
We moved our toilet six inches to fit a bigger vanity, and the crew cut the slab and rerouted the drain in one day. They pressure tested everything before the tile went down. The inspector passed it on the first visit. No leaks, no callbacks.
Our 2003 build had original shutoff valves that were frozen. They replaced the whole rough-in with PEX and set a new Moen valve. Water pressure in the shower is night and day. They also camerad the sewer line while the floor was open and found roots starting.
I got three quotes for a bathroom remodel plumber in gilbert AZ. These guys were the only ones who explained the venting and showed me where the shutoffs would go. They finished the fixture set in half a day and cleaned up everything. Worth every penny.
Frequently Asked Questions
Short answers for the first few minutes. The team can cover the rest.
Still have a question?
Describe what you are seeing and we will point you to the right next step.
+14802885094A simple fixture swap with no layout change sits near the low end. Moving a toilet or adding a second sink means slab cutting and a longer drain run, which pushes the price up. We give you a written number after the walkthrough.
We do. Our crew handles the full plumbing scope: demo, rough-in, slab work, inspection, and final fixture set. You do not need a separate plumber and tile guy. Call us and we will schedule a walkthrough, usually within one business day.
The plumbing portion takes 5 to 10 business days spread across the project. Rough-in is one to two days, the inspection usually happens within 48 hours, and the final fixture set is a half-day. Tile, paint, and cabinets add the rest of the calendar time.
Yes. Any change to the drain, vent, or water supply lines requires a plumbing permit through the city. We pull the permit and meet the inspector on site. Fixture swaps that reuse existing rough-in sometimes qualify as a minor repair, but we confirm that before we start.
Related Services
Other services from the same team.
- Commercial Plumbing ServicesRestaurants, retail and office buildings in gilbert get scheduled maintenance, grease line jetting, fixture repair and code upgrades.
- Residential Plumbing ServicesEverything a house needs: supply lines, drains, fixtures, water heaters, softeners and gas.
- Plumbing Maintenance PlansA yearly visit that flushes the water heater, tests shutoff valves, checks for leaks and inspects the main…
Ready to start your Bathroom Plumbing Remodeling in gilbert?
+14802885094Call us at +1 480-288-5094 and we will schedule a walkthrough, usually within one business day. You get a written scope and a clear price before any demo starts.
Contact pro plumber gilbert
Call +1 480-288-5094 or email info@proplumbergilbert.com and we will get you on the schedule. Tell us what you are seeing and we will tell you what it likely is before we even arrive.